Proper line winding and coil maintenance are essential for successful fishing, and improper winding can affect casting and prolong line life. All this leads to an unlucky day on the water.
In this short article we’ll look at a step-by-step guide to winding up a reel and give some insider tips that will make your day on the water much easier and more enjoyable.
Step 1
You must first determine the coil current for this headland test track and determine the type of track you want to use. Flow is important because too few lines reduce traction and too many lines can lead to poor casting performance and major turning and junction problems.
For a new roll, even if it is delivered on a roll, we recommend that you replace it with a line of your choice.
Step 2
There are several ways to roll up a reel. The traditional method is to attach them to the rod and guide the line from coil to coil through the guide lines.
For the drums this is our preferred method and we will discuss this soon. There are linear coils, which are excellent for bait, normal coils and flying coils, but we are not interested in winding your rotating drum.
The reason for this is that the way you see a lot of people holding a roll, with the label on the outside and on the bar, with a pencil or something to make the roll rotate easily, causes an enormous amount of line rotation through the roll. That means water problems. The method we will use eliminates most of the line curves.
So take your stick and reel and put a rope through the openings to the open ironing reel. You can leave the spool on the ground or ask a friend to hold it for you throughout the process.
Step 3
There are several knots with which a rope can be attached to a spool, but the most popular one today is the flag. Wrap the end of the marker twice around the roll before tying the flag.
After packing twice, leave a neat piece of label behind to make you work a lot of lines. Once the knot is cut, you can cut any line. With the monofilament and the fluorocarbon they can be attached directly to the coil.
Some coils are not designed in such a way that the braid can be directly attached to them. In this case, you should use a few meters of monoblock substrate. Attach the monoblock to the bobbin with the kiosk and then attach the braid to the end of the monofilament. Again, there are a few knots that will work, but our favorite is a double ordinary knot.
Step 4
Once you have tied the line properly, close the handle and pull the line to tighten the knot. During this process you want to keep the line tight on the coil. The most important step here is to reduce the number of line loops.
In the normal position, with the rod and coil facing outwards, check in which direction the rotor and yoke rotate. On the vast majority of the rotating coils it turns clockwise. If this is the case, you want the line to come out of the coil counterclockwise.
Most equipment manufacturers know this, and the equipment is turned counterclockwise with the face of the coil facing you. Otherwise, just turn the spool around so that the back of your face is facing you.
You can put the reel on the ground in front of you or someone can hold it until the line goes in the opposite direction, until your bail bracket clears you.
Step 5
Now that you wind the wire on the coil and keep it tight, the wire leaves the coil and is wound in the same direction by the manufacturer. The rope has a memory, and the twisting of the rope in the opposite direction goes against that memory and makes it twist.
If you follow the steps we have described, place the cord on the reel in the same direction in which it was placed by the manufacturer. This significantly reduces the bending of the line.
Step 6
One thing that confuses a lot of people as they approach the end of the winding process is the rewinding. Never lay so much wire on a coil that it runs out at the lip of the coil.
This will damage the casting, and it will also lead to a waste of knots and confusion. Always leave at least 1/8 space on the lip of the coil.
Step 7
Once you’ve wrapped the coil, decide how to store it. You can make a line come out of the last eye, attach it to the lure and push the rod into the boat, or you can break it.
If you break the supply rod and the reel, we like to stick the end of the trailer with a small piece of tape on the reel to prevent it from winding up in the reel.
Conclusion
There you go! It’s as simple as that. With a little attention to detail, you can easily wind the reel correctly and greatly reduce the amount of rotation of a line while walking.
If you find your way back to basecamp this way, you will get rid of the big fishing when it’s hot.
Synthesis
Title of Article
It’s like winding a spinning drum.
Description
Carpooling is not always easy, especially for beginners. This is an excellent guide to winding a spinning reel.
Author
Name of the publisher
Shaped for fish.
Logo of the publisher
how to spool a spinning reel with braid,spooling a spinning reel with mono,best way to put new line on a fishing reel,how to spool a spinning reel with fluorocarbon,how to spool a baitcaster reel,how to spool a conventional reel,how to spool a spincast reel,how to put monofilament line on a spinning reel
Disclosure: We are a professional review company & our reviews are not biased towards any of the products we review. We test each product thoroughly and give marks to only the very best that is given by our author. We are very independently owned & the opinions expressed here are our own. However, if you purchase anything after clicking the links present in the articles then we get some commissions for it which help maintaining the websites expenses like servers, security etc.